DIR-615 Manual Repeater

The D-Link DIR-615 is a wireless N 300 repeater designed to extend Wi-Fi coverage, supporting 802.11b/g/n standards with speeds up to 300Mbps, WPA/WPA2 security, WPS button for easy setup, four LAN ports, wall-mountable design, and web-based configuration. Below are key sections for features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Wireless repeater with WPS button, Ethernet ports, reset button, power connector, status LEDs.

Installation

Unpack and inspect contents. Choose optimal location for coverage extension.

1. Position repeater: Place within range of existing Wi-Fi router but in area needing coverage.
2. Connect power: Plug power adapter into wall outlet and repeater.
3. Check LEDs: Wait for Power LED to light solid; Wireless LED should blink during setup.
4. Connect via Ethernet: Use LAN port for initial configuration if needed.

WARNING! Keep away from moisture and heat sources. Ensure proper ventilation.

First-Time Setup

Power on repeater; follow setup procedure.

1. WPS method: Press WPS button on repeater, then press WPS on router within 2 minutes.
2. Web configuration: Connect computer to repeater via Ethernet, open browser to 192.168.0.1.
3. Select mode: Choose Repeater mode in setup wizard.
4. Scan networks: Select your main router's SSID from list.
5. Enter security: Input router's Wi-Fi password if required.
6. Apply settings: Save configuration and wait for reboot.

CAUTION! Default IP is 192.168.0.1; ensure no IP conflicts.

Specifications

• Wireless Standards: IEEE 802.11b/g/n
• Frequency Band: 2.4GHz
• Data Rate: Up to 300Mbps
• Antennas: 2 x external fixed antennas
• Ports: 4 x 10/100Mbps LAN, 1 x Power
• Security: WEP, WPA, WPA2, WPS
• Power Supply: 5V DC, 1A
• Operating Temp: 0°C to 40°C
• Dimensions: Standard compact design

Controls and Settings

Access configuration via web interface at 192.168.0.1. Physical controls: WPS button, Reset button.

Web Interface: Setup Wizard, Wireless Settings, Network Settings, Security, Maintenance.

Wireless: SSID broadcast, channel selection, security settings. Network: IP address, DHCP settings. System: Admin password, firmware upgrade, backup/restore. Status: Connection status, client list, statistics.

Connecting Devices

Wireless: Connect to repeater's SSID. Wired: Use LAN ports for Ethernet devices.

1. Wireless devices: Scan for repeater's SSID (usually router SSID with _EXT).
2. Enter security: Use same password as main router.
3. Wired devices: Connect Ethernet cable from device to LAN port.
4. Verify connection: Check status LEDs and device network settings.

Tip: Repeater SSID may be same as router or different based on configuration.

Repeater Mode Setup

Extends existing Wi-Fi network coverage.

1. Access web interface: Connect to 192.168.0.1.
2. Select mode: Choose "Repeater" in setup wizard.
3. Site survey: Scan for available wireless networks.
4. Select main router: Choose your router's SSID from list.
5. Security settings: Match router's security type and enter password.
6. Apply settings: Save and wait for connection establishment.
7. Verify: Check Wireless LED turns solid when connected.

WARNING! Ensure repeater is within good signal range of main router.

Security Features

Wireless Security: WEP, WPA, WPA2 encryption. WPS: Push-button connection. MAC Filtering: Restrict device access. Admin Access: Password protect web interface.

Care & Maintenance

Unplug before cleaning. Use dry cloth only; no liquids. Keep firmware updated for performance and security.

CAUTION! Do not block ventilation openings. Avoid extreme temperatures.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE marked for European compliance. RoHS compliant. For support, visit www.dlink.com or contact technical support.

Troubleshooting

Reset: Hold reset button for 10 seconds to restore factory defaults.

Service: www.dlink.com/support; check website for firmware updates.